Industrial Shutter Doors
These doors are suitable for shops, commercial centers, and warehouses due to the protection they provide.They are characterized by Strength and durability, a variety of colors, easy installation and simple maintenance.They can be equipped with a central Italian motor, a side motor,or a manual chain system.
The manufacturing of shutter doors is one of the top priorities of Elite Factory,and this industry is carried out using the finest raw materials, ncluding:Galvanized iron,thick slats with thickness ranging from 0.8 mm to 1.00 mm, Door tracks made from galvanized iron. Door operating systems available in sizes that match the door dimensions.
THE NUMBER OF TYPES OF SHUTTER DOORS IS AS FOLLOWS:
Insulated Shutters (Stainless Steel)
Specification
Curtain:
Interlocking Hat profle stats thickness 0.8mm produced from stainless steel Interlocking Flat profile perfocated stats thickness 0.8mm produced from stainless steel Size of perforated whole 2.5mm.
End clips: Slates are sec
Are secured in the position by nylon end clips on the alternatives which stop them from moving sideways. therefore preventing the curtain from lateral movement
Bottom Rail:
The bottom rail is fabricated from double stainless steel angle size 40x40x4 mm, 50x50x5mm thick (its depend on the door size). with vinyl astragal Bottom bat provide reinforcement to bottom of curtain.
Guides:
Produced from 2mm thick steel strip. hot dipped galvanized and cold formed into channel U section
60mm x 30mm, 100mm x30mm (its depend on the size door).
Axle and Drum (Center Motor):
Asde shall be a steel pipe 60mm or 76mm (its depend on the size door) to ensure a rigid structure to give a high factor of operating safety and minimum efication.
Shaft (Side Motor)
Using barrel 133mm x 4mm 300mm x 6mm (its depend on the size door) to give high factor of operating safety of and minimum deflection.
Brackets
Galvanized steel plate of size 400mm x400mm x 4mm thickness is used to make bracket. This bracket holds dangle along with (central motor). Made up of 3mm thickness of size 4450mm L x 425mm H with two gusset plates. This gives stability to the bracket. Also for door bigger than 6 meter the bracket of size 70mm L x 560mm H with thickness of 5mm used. This bracket has two gusset plates to give stability. The brackets are of steel with powder coating done (Side Motor-Si) Brackets are made of mild steel plates, 515x300x3.5mm, 580x320x4mm thick (Its depends on the door size) these brackets support the drum and curtain assembly which are attached to the inside wall of the building. Brackets are factory painted with under primer to protect from corrosion. (Rollc Motor).
Insulated Shutters (Aluminum)
Specification
Curtain:
Interlocking Hat profile slats thickness 1.2mm roduced from Aluminum Interlocking Flat profile perforated slats thickness 1.2mm produced from aluminium Size of perforated whole 3.0mm.
End clips: Slates are sec
are secured in the position by nylon end clips on the alternatives which stop them frons moving sideways, therefore preventing the curtain from lateral movement
Bottom Rail:
The bottom rail is fabricated from double Aluminum angle size 40x40x4mm 50x50x5mmm thick (Its depend on the door size), with vinyl astragal Bottom bar provide reinforcemern to bottom of curtain
Guides:
Produced from 2mm thick steel strip, hot dipped galvanized and cold formed into channel U section 60mm x 30mm, 100mm x 30mm (Its depend on the size door)
Axle and Drum (Center Motor):
Asde shall be a steel pipe 60mm or 76mm (its Depend on the size door) to ensure a rigid structure to give a high factor of operating safety and minimum deflection
Shaft (Side Motor)
Using barrel 133mm x 4mm 300mm x 6mm (lis depends on the door size) to give high factor of operating safety and minimum deflection.
Brackets
Galvanized steel plate of size 400mm x400mm x 4mm thickness is used to make bracket. This bracket holds dangle along with (central motor). Made up of 3mm thickness of size 4450mm L x 425mm H with two gusset plates. This gives stability to the bracket. Also for door bigger than 6 meter the bracket of size 570mm L x 560mm H with thickness of 5mm used. This bracket has two gusset plates to give stability. The brackets are of steel with powder coating done
(Side Motor-Si) Brackets are made of mild steel plates, 515x300x3.5mm, 580x320x4mm thick (Its depends on the door size) these brackets support the drum and curtain assembly which are attached to the inside wall of the building. Brackets are factory painted with under primer to protect from corrosion. (Rollc Motor).